Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterAndersen Door Installation in Tampa: What to Know First
Andersen door installation in Tampa typically runs between $1,800 and $6,500 depending on the series, glass package, and whether the existing frame comes out or stays put. We’re an independent Andersen service provider, not a factory branch, which means we quote the work honestly and register your warranty layers in writing before we leave the driveway. Most single-door installs take one visit, usually four to six hours on site.
This page is for homeowners in Tampa who already own an Andersen door, or are about to order one, and want it set square the first time. If what you’re holding is misaligned, binding, leaking daylight around the frame, or wearing out its hardware, call (813) 320-9346 and a person answers. Always.
How Andersen Products Fail - and How We Fix Them
- Andersen 400 Series hinged patio doors binding in summer humidity. Tampa’s wet season pushes wood-fiber cores to expand, and a door that swung fine in February starts dragging on the threshold by July. The fix is usually re-shimming the hinges and adjusting the reveal, not planing the slab. We measure the gap with feeler gauges first so the door stays on the same plane it was engineered for.
- E-Series French doors losing their weather seal at the astragal. The aluminum-clad E-Series is a common sight in Bayshore and Davis Islands homes, and the interlocking astragal wears at the center joint over years of salt air and hard sun. We replace the weatherstripping with the correct profile and reset the active panel so the meeting stiles close flush with about 1/8 inch of compression. Too tight and the lock fights you. Too loose and the afternoon rain gets a say.
- 200 Series storm doors with sagging hinges and hairline cracks at the corners. The 200 Series is a lighter door, and Tampa’s gusty squall season works its fasteners loose over time. We see the top hinge plate pulling away from the jamb and the corner joints starting to open. Sometimes the fix is a new jamb bracket and a re-set. Sometimes the slab is past saving and we’ll tell you that plainly instead of patching it.
- A-Series entry doors with finish delamination from direct west-facing sun. Tampa afternoons are brutal on dark-painted entry doors. The A-Series carries a strong warranty, but the finish can cloud or delaminate early if the door was installed without an adequate overhang or storm protection. We strip, prep, and refinish to the specs that preserve the warranty, and we’ll be honest if a replacement makes more sense than another coat.
- Older Narroline gliding doors with worn rollers and track wear. We still get calls on the original Narroline line, which Andersen retired years ago. The rollers flatten into ovals, the track grooves deepen, and the door grinds instead of glides. Replacement rollers are still manufactured by aftermarket suppliers, and we match the wheel diameter and bracket profile so the door carries its full weight correctly.
Our Andersen Door Installation Process
A door only behaves the way it should if the opening it sits in is truthful. Here’s how we work every Andersen job in Tampa.
- 1
We inspect the opening first. Rough framing gets checked for square, plumb, and level in three places per side. If the house has settled, we find it before any new door goes in.
- 2
We measure twice. Every opening gets measured at the top, middle, and bottom of each jamb. The rule Dale Kessler keeps on the whiteboard hasn’t changed in many years: if the pane is not true, the job is not done.
- 3
We walk you through the parts decision on paper. When an Andersen component needs replacing, we show you OEM pricing next to quality aftermarket options. You see exactly what you’re buying before a single fastener gets turned.
- 4
We set the door in and shim it true. The frame gets anchored and the slab hung on the hinges with the correct reveal all the way around. Then the door gets cycled open and closed, not once, but through the full swing, while we watch the gap with a flashlight.
- 5
We air-seal and flash the rough opening. Tampa sees more than fifty inches of rain a year. Water intrusion around a door frame is not a guess, it’s a matter of doing the flashing in the right sequence so water can only go down and out.
- 6
We register both warranty layers in writing and walk you through the finished work. The manufacturer warranty and our 90-Day Done Right Promise get documented before the truck leaves the driveway. We show you the paperwork. You keep a copy.
What Andersen Door Installation Costs in Tampa
Straight numbers from the work we’ve done across Tampa: you should plan around $1,800 to $4,200 for a standard single-swing Andersen door installed, including the new door, hardware, and trim work. Double French doors run higher, typically $4,000 to $6,500 depending on glass package and whether the opening needs reframing. Full-frame installation that pulls the old jamb and rebuilds the rough opening adds $600 to $1,200 to any of these numbers.
What moves the price most is the condition of the existing rough opening. If termite damage or rot has worked the king and jack studs, the framing repair comes before anything else. If the opening is sound, the job is far simpler. Call (813) 320-9346 for a free estimate. We price the work in writing with no surprise line items after the fact.
Why Tampa Homeowners Call TruePane Windows & Doors for Andersen Work
We do not install a door and then vanish into a call center queue. A live person answers the phone 24 hours a day, seven days a week, and the person standing inside your home wears a uniform, has passed a background check, and measures every opening twice. Our installers are trained in-house, apprenticed through the trade the slow way, and they know Andersen doors the way a mechanic knows a particular engine.
When the discussion needs more than one brand on the table, we’ll show you Pella, PGT, and CGI side by side on paper so you can compare costs and glass packages without the sales fog. Andersen is what you asked about, and we’ll do right by it. But a square deal means you see the options. And every job, regardless of brand, is covered by the 90-Day Done Right Promise. If it’s not done right, we make it right. That’s the whole policy.
Dale Kessler grew up in Seminole Heights and still lives about six blocks from where he learned to ride a bike. He founded TruePane in 2008, but the standards come from a father who ran a building-maintenance outfit for thirty years, where a callback was a character flaw, not just an inconvenience. If it needs to be in writing to be true, we will put it in writing.
FAQs
It can, and usually does, for the parts and labor coverage on the installation. Andersen’s written warranty protects against manufacturing defects, not against a door that was hung out of square. We register both warranty layers in writing on every job in Tampa, so there’s no question about who covers what if something fails.
Yes, provided the finish is a current Andersen offering. Sandtone, Terratone, white, and the oil-rubbed bronze variants all have matching hardware profiles. For discontinued finishes, we will show you the closest OEM option and tell you honestly if the match is close or dead-on.
If the slab is sound and the frame is tight, a hinge adjustment and re-shim fixes most binding. If the slab itself has delaminated or the frame has pulled away from the house framing, replacement costs less than fighting a losing door. We’ll tell you which side yours falls on before quoting either path.
A single entry or patio door is usually one visit, four to six hours on site. Double French doors and full-frame installations with framing repair take a full day, sometimes a day and a half. We’ll give you a written timeline before the job starts, and we’ll be there when we say.
When a door replacement is what the permit office calls “like for like” in the same rough opening, a permit is often not required. When the opening size changes, structural framing is involved, or it’s part of a broader exterior renovation, we pull the permit and close out the inspection. Call (813) 320-9346 and we’ll tell you straight what your project needs.
Call for Your Free Andersen Door Estimate in Tampa
If your Andersen door is binding, leaking, sagging, or just not the door it was when you bought the house, call (813) 320-9346. A person answers, and we’ll schedule a time for one of our technicians to look at the opening and give you a written line-item price. No pressure, no change orders later, and no call center runaround.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Tampa and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.