Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTherma-Tru Shingle, Tile & Metal Roofing in Tampa: What to Know First
We provide independent Therma-Tru shingle, tile and metal roofing service across Tampa, with most repairs completed in a single visit and straightforward pricing agreed before any work begins. Typical Therma-Tru roofing-related repairs in Tampa homes run between $185 and $560, and full component replacements are quoted line by line so you see exactly what you’re paying for. If you own a Therma-Tru door or window system and the roofing integration around it is failing, call (813) 320-9346 and a live person answers. This page is for Tampa homeowners who own Therma-Tru products and need the surrounding shingle, tile or metal roofing work handled by people who understand how that brand integrates with a Florida roof.
How Therma-Tru Products Fail - and How We Fix Them
Therma-Tru builds fiberglass and steel entry systems, storm doors, and the Classic-Craft, Pulse, and Benchmark lines you see across Tampa neighborhoods like Davis Islands, Seminole Heights and Westchase. The roofing connection is where most failures happen, and they fail in predictable ways we’ve been correcting for years.
- Pulse series entry systems and header flashing separation. The Pulse line uses a wider frame profile than older Therma-Tru units, and when a Tampa roofer replaces shingles without re-flashing the door header, water tracks behind the brickmold and rots the sub-sill. We remove the first course of shingles above the door, install proper step flashing, and re-seat the brickmold against the new flashing. This is the single most common Therma-Tru roofing call we run in Tampa.
- Benchmark steel doors with failed drip caps. Therma-Tru ships these with an aluminum drip cap that is too short for the tile roof profiles common in South Tampa and Bayshore. Stucco or tile work above the door channels water behind the cap. We replace the factory cap with an extended profile that tucks under the tile course and over the door’s top flange. It is a simple fix, but you would not know to look for it unless you’ve seen it a hundred times.
- Classic-Craft fiberglass frames and roof valley runoff. Fiberglass frames do not rot, but the framing lumber behind an improperly flashed Classic-Craft install does. In Tampa’s wet season, a roof valley that discharges near an entry door saturates the jack studs. We see this in older Hyde Park and Palma Ceia homes where valleys were built to code forty years ago but the adjoining door was replaced without extending the valley flashing. We correct the valley termination and rebuild the rough opening if needed.
- Therma-Tru sidelight units and tile roof kickout flashing. Sidelight assemblies are more vulnerable than solid doors because the glass-to-frame seals flex with heat. Tampa’s tile roofs hold heat against the wall, and without a proper kickout at the roof-to-wall intersection, water runs down the wall and pools at the sidelight base. We install code-compliant kickout flashing that moves water away from the door system entirely.
- Storm door installs over Therma-Tru entry systems with metal roof condensation. Metal roofs shed water fast, but standing seam profiles create condensation at dawn when Tampa temperatures swing. A storm door mounted tight against a Therma-Tru entry door traps that moisture in the sill track. We address it with proper standoff clearances and drainage channels, not just caulking the seams.
Our Therma-Tru Shingle, Tile & Metal Roofing Process
A Therma-Tru roofing job around a door or window follows the same discipline we apply to every glazing repair. Here is what happens after the call.
- 1
We answer. A live person takes your call at (813) 320-9346, day or night. You describe the problem and we schedule the visit. We’ll be there when we say.
- 2
We inspect the roofing-to-door connection. Our technician examines the flashing, the shingle or tile course above the opening, the drip edge, the rough opening and the frame itself. We photograph everything and show you what we found.
- 3
We put the fix on paper. You get a written line-item quote. If the repair needs OEM Therma-Tru trim or a quality aftermarket flashing profile, we explain the difference and the cost of each. No surprise line items later.
- 4
We do the work. Step flashing, drip caps, kickout flashing, sealant work around the roofing-to-frame junction: it gets done the way Dale Kessler learned it at the Hillsborough Community College shop floor: measured twice, set once, checked with a level before we call it finished.
- 5
We test and verify. We run water over the repaired area and inspect the interior side of the rough opening for any moisture path. If the pane is not true, the job is not done. Same rule applies to flashing and roofing junctions.
- 6
We register our work in writing. The 90-Day Done Right Promise applies to the repair. If it is not done right, we make it right. No paperwork fights, no arguing.
What Therma-Tru Shingle, Tile & Metal Roofing Costs in Tampa
Here is what we see in Tampa, honestly. The lower figure assumes the frame and rough opening are sound. The higher figure accounts for rotted builders and hidden damage we could not see until the old flashing came off.
- Header flashing repair above a Therma-Tru entry door (shingle roof): $185-$340
- Extended drip cap install over a Benchmark door (tile roof): $220-$410
- Valley termination correction near a Classic-Craft entry: $310-$560
- Kickout flashing install at roof-to-wall with sidelight unit: $260-$480
- Rough opening rebuild plus flashing (rotted framing discovered): $640-$1,250
What moves the price: roof type (tile work costs more than shingle work because tiles must be lifted and re-set), accessibility, and the condition of the wood underneath. We do not charge for the estimate, and we do not change the price mid-job without putting the reason on paper first. Call (813) 320-9346 for an exact quote on your Therma-Tru roofing repair in Tampa.
Why Tampa Homeowners Call TruePane Windows & Doors for Therma-Tru Work
We are not the cheapest bid in Tampa, and we do not intend to be. We are the company homeowners call after another contractor has been out twice and the door still leaks. TruePane Windows & Doors was founded in 2008 by second-generation glazier Dale Kessler, who grew up in Seminole Heights and still lives about six blocks from where he learned to ride a bike. The standard on every job is The Keystone Standard: both warranty layers registered in writing, durations stated, before the truck leaves the driveway. Our technicians are background-checked and uniformed, and they work in your home the way they would work in their own mother’s. We are also an authorized installer for more than a dozen manufacturer lines including Andersen, Pella, Marvin, Milgard, Jeld-Wen, PGT, CGI, CWS and ES Windows, so if a Therma-Tru unit is beyond saving and you choose to replace, we can quote side by side on paper so you see exactly what you are buying. If it needs to be in writing to be true, we will put it in writing.
FAQs
No. As an independent Therma-Tru service provider, we take care to work within Therma-Tru’s installation tolerances when we repair flashing and roofing junctions, and we document the condition of the frame and rough opening before and after the repair. We are not affiliated with Therma-Tru, and we will never imply we are. But our repair practices preserve the original installation geometry Therma-Tru designed around. Call (813) 320-9346 if you have a warranty question and we will talk it through.
Most Therma-Tru roofing junction repairs are completed in a single visit, and we schedule based on how urgent the water intrusion is. A live person answers 24 hours a day, 7 days a week, so you are never leaving a message and hoping. We’ll be there when we say, and the repair usually takes between two and four hours depending on the roof type.
If the door slab, hinges and weatherstrip are sound, repair the flashing and rough opening. We will not sell you a new door when a $300 flashing repair fixes the problem. But if water has been running for two or three Tampa rainy seasons and the sub-sill or jack studs are gone, replacement is the honest recommendation, and we will show you the rot on camera before we suggest spending that kind of money.
We use OEM Therma-Tru trim and sill components whenever the existing unit requires an exact match, and we use quality aftermarket flashing and drip cap profiles where the factory part was undersized for Florida roof conditions. We explain which is which on the written quote before any work starts. You decide with the facts in front of you.
Only if we open up a roof-to-wall junction and find rotted framing that was hidden behind sheathing or stucco. In that case, we stop work, show you the damage, put the additional scope on paper, and get your approval before proceeding. No change orders you never saw coming. That is a square deal.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Tampa and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.